Details (click to enlarge)
    Angels (click to enlarge)
    Certificates
    Components
    Product Icons
    • 3 years
    • T8 (G13)
    • 1-10V (Optional)
    • Triac
    • <12%
    • -40ºC +65ºC
    • A+
    Product features

    1. Retrofit system for luminaires with traditional fluorescent tubes.
    2. Its rotary heads allow adjusting the angle of light emission for any type of application.
    3. Incorporates a starter (fuse) to make it easier to replace without needing to rewire the luminaire.
    4. Its translucent cover creates a perfectly homogenous visual effect that can not be differentiated from the traditional fluorescent.
    5. The aluminum structure allows fast chip cooling, high heat conduction efficiency and high thermal dissipation performance.
    6. Led-by-pass technology: If a led is damaged, it will not affect the rest, nor will it increase its operating current.
    7. Isolated internal driver with intelligent constant current technology, stable current output.

    Light distribution image (click to enlarge)
    LRE8
    LRE8
    Product dimensions (click to enlarge)

    (see product parameters table for details)
    Product RangeIndoor
    Product FamilyRetrofit lamps
    Product Model
    Series ReferenceT8AP
    Warranty3 years
    Lifespan @ Ta=25ºCL70 F10 30.000h
    Lifespan @ Ta=40ºCL70 F10 25.000h
    Voltage (V)85-265VAC
    Frecuency (Hz)50-60 Hz
    Power Factor (PF)>0.95
    Flicker (%)0%
    Total Harmonic Distorsion (THD %)<12%
    Switching cycle> 50.000
    Máx. Starting Time (s):0, 5 sg
    System Luminous Efficacy (Lm/W)95 lm/W ±10%
    Color Render Index (CRI >Ra)>80
    Correlated Color Temperature (CCT ºK)3000K~6000K
    Color Consistency (SDCM)< 5
    Warm-up Time to 60% Light Output (s)Instant
    Suitable for accent lightingNo
    Beam Angle (Degrees)180º
    Index of protection (IP):IP20
    Surge ProtectionStarter (fuse)
    PCB TypeMC-PCB
    PCB MaterialAluminium
    Thermal ViasYes
    Led Bypass ProtectionYes
    Overheating ProtectionYes
    BrandEpistar
    TypeSMD
    Model2835
    Internal or ExternalInternal
    Isolated or NotIsolated
    Thermal Interface Material (TIM)Yes
    Body MaterialAluminium
    Fins MaterialAluminium
    Extra Cooling SystemThe whole structure of radiation
    Body MaterialExtrusion of aluminum
    FinishingAluminium
    Cover MaterialPC
    Cover TypeTranslucent, clear (optional)
    Locking SystemStainless steel screws
    Diffuser MaterialPC
    Storage Temperature (ºC)-40ºC +65ºC
    Operating Temperature (ºC)-20ºC +55ºC
    Operating Humidity (%RH)5-95ºRH
    Dimming Function1-10V (Optional), Triac
    Other Sensors OptionsPhotoelectric, Movement, Other
    Wired Communications CompatibilityNo
    Wirless Communications CompatibilityNo
    Existing luminairesAccording to assembly instructions
    New LuminairesAccording to assembly instructions
    Electric Connection1 side power
    Angle AdjustmentNo
    Replaceable Light SourceNo
    Replaceable DriverNo
    Replaceable LensNo
    Replaceable CoverNo

    Please note: For this application you will need the safety fuse link supplied as a separate item. Stock code: T8AP
    No changes to the wiring of the fitting are required except for the removal of the power factor correction capacitor. (See the Diagram below)
    1. Please make sure that the power supply to the Fitting to be worked on has been switched off.
    2. Remove the starter and fluorescent lamp from the fitting. If there is a Power factor correction capacitor present this should also be removed. The ballast if not completely removed must be crossed out with a permanent marker.
    3. Paste the supplied warning stickers and wiring diagram onto the fitting in an area where it will be visible to any person wishing to change lamps or do maintenance on the fitting. On the inside wiring diagram sticker must be next to the terminal block.
    4. Remove the LED Tube conversion unit from the packaging and install it as you would with a fluorescent lamp.
    5. Insert the T8AP  Fuse link in the starter holder.(Marked F in the diagram above)
    6. Reconnect the supply and test the fitting

    Matters need attention 1. Before use, should carefully read the instructions , to avoid accidents and damage.
    2. Please wear gloves to avoid injury before installation work.
    3. Lighting installation, and wiring work must be carried out in the absence of power.
    4. Power line joints must do insulation , waterproofing treatment.
    5. Do not look directly at the light emitting LED lighting in close distance, ensure not hurt the eyes.

    ModelPcs/CtnLong (mm)Width (mm)Height (mm)Gross Weigth (kg/ctn)
    600mm256351701455,8
    900mm259351701459,2
    1200mm25123517014510,64
    1500mm25153517014511,76
    Product Builder (start building your product)
    model
    T8AP
    power
    23W
    18W
    9W
    12W
    color CCT
    CW
    6000K
    NW
    4000K
    PW
    5000K
    WW
    3000K
    voltage
    120
    100V-120V
    240
    200V-240V
    UNV
    90V-305V
    lens
    LRE8
    Symmetric distribution of 180º
    control
    1-10V
    Dimming 1-10V
    NC
    No control
    TRIAC
    Triode for Alternating Current
    diffuser
    M
    MILKY
    T
    Transparent
    Product Parameters
    ReferenceSystem PowerBaseSystem Efficacy (Lm/W)Luminous Flux (Lm)Lumen maintenance @ Ta=25ºCEnergy efficiency labelDimensionsWeight (Kg)
    @ 3000K @ 4000K @ 5000K @ 6000K
    EXST8AP9W6009WT8 (G13)95lm/W ±10%814866899933L70 F10 30.000hA+Ø26*600mm0,21 kg
    EXST8P12W90012WT8 (G13)95lm/W ±10%1085115511991244L70 F10 30.000hA+Ø26*900mm0,35 kg
    EXST8P18W120018WT8 (G13)95lm/W ±10%1628173217991866L70 F10 30.000hA+Ø26*1200mm0,41 kg
    EXST8P23W150023WT8 (G13)95lm/W ±10%2080221322992384L70 F10 30.000hA+Ø26*1500mm0,45 kg

    C/ Ventalomar 1, 45007,
    Toledo Spain
    (+34) 925 115 522
    info@enarlux.es

    Enarlux Colombia S.A.S. Mall Toma Real, Carrera 9 #10 07, Local 24,
    Neiva city - Huila, Colombia
    (+57) 322 760 11 25
    info@enarlux.co

    9th Floor, Amtel Building,148 Des Voeux Road Central –
    Republic of China - Hong Kong
    Tel : (852) 9547 1251
    (GMT +08:00 hours)

    ENARLUX born under the idea of being a world leader in the design and manufacture of LED lighting products with high quality and reliability.

    ENARLUX performs strict auditing processes and manufacturing control, as well as a comprehensive selection of components that ensure a finished product of high durability and high performance.